BuckMaster 21 Manual de instalación

BuckMaster AIR-TIGHT ZERO CLEARANCE FIREPLACE INSTALLATION/OPERATOR’S MANUAL FOR YOUR SAFETY - Do not store or use gasoline or other flammable vapo

8 HOT AIR DUCT INSTALLATION The BuckMaster Fireplace can be used to heat a single room or an entire house. The diagrams on this and the following thr

9 TYPICAL DUCTWORK LAYOUT FOR CENTRAL HEATING Approved for United States and Canada NOTE: DUCT WORK MAY BE RUN OVERHEAD OR

10 CENTRAL HEATING DUCT SYSTEM CLEARANCES All hot air ductwork must be 8" diameter B-Vent through the initial wall or ceiling penetration. Single

11 OPTIONAL HOT AIR DUCT KIT 2 - 8" diameter, 12" lengths, B-Vent 2 - 8" diameter 90o elbows, B-Vent OPTIONAL 10" x 10" GR

12 FLUSH FIREPLACE INSTRUCTIONS WHEN INSTALLED WITH 8" DUCT KIT 1. Fit a 90o elbow to the to of each duct sections. Push down firmly to snap lo

13 FRAMING-IN AND FINISHING INSTALLATION The BuckMaster fireplace has been designed so it can be framed-in using standard combustible building materia

14 FIREPLACE DIMENSIONS (in inches) NOTE: Rough opening size: 38 1/2" WIDE x 52" HIGH

15 NON-COMBUSTIBLE FACING CUT-OUT DIMENSIONS Required for tile or marble facing SET-BACK FOR FACING OPTIONS

16 ROUGH OPENING DIMENSIONS ROUGH FRAMED FLOOR LEVEL INSTALLATION SHOWN WITH OPTIONAL 10" x 10" GRILL KIT HEADER DETAIL ROUGH FRAMED RAI

17 FINISHING DETAILS AND OPTIONS PARTIALLY OVERLAPPED NON-COMBUSTIBLE FACING FINISHING HEARTH: A non-combustible hearth (e.g. ceramic tiles, stone,

18 STANDARD FORCED AIR FAN WIRING OF FAN SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN. The forced air fan comes factory installed and includes the

19 DOOR HANDLE INSTALLATION 1. Screw wooden handle onto shank and insert into door. 2. Secure with locking nut. 3. Slide on washer and latch cam

20 NEVER BURN COLORED PAPER, PAINTED WOOD, WOOD WITH NAILS, ETC. THESE MATERIALS CONTAIN COMPOUNDS THAT WILL DAMAGE THE UNIT’S CATALYTIC COMBUSTOR. Do

21 STARTING A FIRE: 1. Pull out the two slide draft controls so they are fully open. 2. Open the by-pass damper by giving the handle at the top ce

22 3. Door frame - The gold plated frame should be cleaned with appropriate metal cleaner. Do not use steel wool or other abrasives. 4. Creosote -

23 NOTE: If you have installed a brick solder course over the top grill, the catalytic combustor must be removed through the firebox. 1. Remove fir

24 BY-PASS DOOR REPLACEMENT All materials subjected to high temperatures will eventually breakdown. If during regular inspection of the firebox you d

25 ITEM DESCRIPTION PART # ITEM DESCRIPTION PART # 1 Top Grill PO CL60-89787 13 Optional 8" Hot Air Duct x 12" N/A* 2 By-pass Hand

26 ITEM DESCRIPTION PART # ITEM DESCRIPTION PART # 25 Inner Top PS CL60-24160 42 Glass Rope RP FTV125X1.00GA 26 Back Insulation N/A 43 D

27 ITEM DESCRIPTION PART # 57 Rear Offset Brackets PS CL60-24040 58 Slide Plate PS CL60-24034 59 Compression Springs PH 141SPRING 60 3/16&qu

1 TABLE OF CONTENTS INTRODUCTION ... 3 GEN

28 NEW BUCK CORPORATION (NBC) “LIMITED WARRANTY” FOR THE BuckMaster STOVE PLEASE READ THIS WARRANTY CAREFULLY PRODUCTS COVERED This warranty covers

If for any reason you are dissatisfied with the suggested procedures, you may contact us in writing at: New Buck Corporation Customer Service Dep

2

3 INTRODUCTION Thank you for your purchase of the BuckMaster Zero-Clearance Fireplace. By following the instructions in this manual you can be assur

4 CLEARANCES TO COMBUSTIBLES HOT AIR DISTRIBUTION The high BTU output of the BuckMaster fireplace makes it an excellent heat source. The diagrams on

5 INSTALLATION PARTS NEEDED CHECKLIST: 1. BuckMaster Fireplace 2. Hot air duct kit 3. 6" wide steel floor safety shield 4. Approved Chimney in

6 INSTALLING THE CHIMNEY Follow chimney manufacturer’s instructions for proper installation. Be sure the chimney is equipped with the corresponding an

7 COMBUSTION AIR DUCT It is required that a separate source of outside combustion air be provided for all installations. This is particularly importan